- Does subfloor go under bathtub?
- How much does it cost to install a standard bathtub?
- How long does it take to install a bathtub?
- How do I measure for a new bathtub?
- Are all baths a standard size?
- How hard is it to install a bathtub?
- How long does it take to tile around a bathtub?
- What is the size of a standard bathtub?
- How much does the average walk in tub cost?
- Is it worth it to refinish a bathtub?
- What is the minimum size of a bathtub?
- Can I resurface my bathtub myself?
Does subfloor go under bathtub?
Bathroom floors are notorious for suffering water damage and the area under the bathtub is no exception.
Flooring repairs can be intimidating, but the subfloor under the tub generally consists of plywood secured over floor joists and is fairly simple to replace — once you get access to it..
How much does it cost to install a standard bathtub?
Bathtub CostsItemUnit CostMaterials Cost$700each3. + Labor Cost (plumber)$42per hour4. + Labor Cost (remove and replace)$36per hourTotal Cost$1,006each2 more rows
How long does it take to install a bathtub?
around 6-9 hoursA new tub installation will take around 6-9 hours and will cost you between $540 and $1,620 in labor.
How do I measure for a new bathtub?
When measuring a bathtub, always make sure to measure to the farthest extremity of the bathtub’s edges to make sure it will fit. If you’re measuring a bathtub with different heights around the top edge, make sure to measure to the highest point so you don’t encounter any installation problems later.
Are all baths a standard size?
Standard bath size As it is commonly accepted that the standard bath width is 700mm, a wide bath is considered to be any bath with a diameter of 800mm and above. Large baths with dimensions over 1800mm in length and over 800mm wide tend to be freestanding baths.
How hard is it to install a bathtub?
Replacing an old bathtub with a new bathtub is a very difficult project. Much of the tile on the walls will be damaged during the removal. If the old tub is readily accessible, the project can move quickly. If you have to open a wall to remove the old tub and position the new tub, the task is much harder.
How long does it take to tile around a bathtub?
Existing Tile Tub Surround – You really can demo this in about an hour maybe two. It is really important that you protect the tub so you do not damage it.
What is the size of a standard bathtub?
In general, standard dimensions will give you a rough figure for the size of the bathtub. However, they all vary depending on the shape and type of bathtub you are looking to purchase. For a typical standard, wall-wall bathtub, the measures will be roughly 60 inches long, 30-32 inches wide.
How much does the average walk in tub cost?
The typical cost of installing a walk- in tub is between $700 and $1,500 for a total cost of $5,000-$7,000 on average including the tub.
Is it worth it to refinish a bathtub?
Bathtub refinishing is worth the money if your tub is in good working condition. The reglazing process can remove surface imperfections, like scratches, shallow cracks, and stains. But if your tub is old, leaking, or full of mold, reglazing is just a waste of money. You’ll have to buy a new tub soon anyway.
What is the minimum size of a bathtub?
60 inches longBathtubs. While there are no code requirements for tub size, minimum clear floor space alongside a bathtub should be at least 60 inches long (the length of a standard tub) and 30 inches wide. Always allow clear space for access to plumbing and/or whirlpool motors.
Can I resurface my bathtub myself?
Do-it-yourself bathtub refinishing is even more inexpensive than hiring the pros, but you will end up with an inferior finish that is more likely to peel. … You can buy DIY kits that include a quart of epoxy with hardener, latex gloves, steel wool, brush, cleaning solution, cleaner/thinner, and safety goggles.